- 您现在的位置：买卖IC网 > Sheet目录342 > MAXQ610-KIT# (Maxim Integrated Products)EVALUATION KIT FOR MAXQ610
Evaluates: MAXQ610
General-Purpose LEDs
The MAXQ610 EV kit board has four general-purpose
LEDs labeled DS1, DS2, DS3, and DS4. Each anode is
connected to the board’s VDD through a 100? resistor, and
each cathode is connected to a processor port 3 pin through
a jumper as specified in Table 3 . By setting the related port
pin as an output, each LED can be illuminated by setting the
port pin output register bit (PO3.x) to a logic 0.
JTAG Interface
A USB-to-JTAG/1-Wire Adapter (provided with the EV kit)
is used to program and debug applications running on the
MAXQ610 EV kit board. Refer to the MAXQ USB-to-JTAG/
1-Wire Adapter data sheet and user ’s guide found in the
EV kit Resource Package. Connect the 10-pin ribbon cable
from the USB-to-JTAG/1-Wire Adapter ’s JTAG connector to
connector P5 on the MAXQ610 EV kit board, being careful
to note the polarity. Tools such as the Microcontroller Tool
Kit (MTK) and IAR’s Embedded Workbench have built-in
support for loading applications through the JTAG interface
and using all the MAXQ610 debug functionality (break-
points, register and memory reading, etc.).
Figure 3. MAXQ USB-to-JTAG/1-Wire Adapter
IAR Embedded Workbench is a registered trademark of IAR
Systems AB.
www.maximintegrated.com
MAXQ610 Evaluation Kit
Getting Started
IAR Embedded Workbench
IAR Embedded Workbench ? is the primary IDE used for
coding in C with the MAXQ610. The latest version of IAR
can be obtained online from the MAXQ Development Tools
webpage at www.maximintegrated.com/MAXQ_tools .
IAR offers both time-limited and size-limited licenses of
the IDE for evaluation. Download and execute the installer.
Follow the installer directions to install the software.
Table 3. General-Purpose LED
Connections
LED JUMPER PORT PIN
DS1 JH22 P3.0
DS2 JH23 P3.1
DS3 JH24 P3.2
DS4 JH25 P3.3
Maxim Integrated │ 6
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MB2146-401-01A
KIT STARTER F2MC-8FX 3V
MB2146-401-03A
KIT STARTER F2MC-8FX 5V
MB2146-410A-01-E
KIT STARTER MB95200/210H SERIES
MB85R1001ANC-GE1
IC FRAM 1MBIT 150NS 48TSOP
MB85R1002ANC-GE1
IC FRAM 1MBIT 150NS 48TSOP
MB85R256FPFCN-G-BNDE1
IC FRAM 256KBIT 150NS 28TSOP
MB85RC128PNF-G-JNE1
IC FRAM 128KBIT 400KHZ 8SOP
MB85RC16PNF-G-JNE1
IC FRAM 16KBIT 1MHZ 8SOP
相关代理商/技术参数
MAXQ610K-UEI+
制造商:Maxim Integrated Products 功能描述:MAXQ610 BLANK 44TQFP UEI - Rail/Tube
MAXQ610X-0000
功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MAXQ610X-0000+
功能描述:MCU 16BIT W/IR MODULE BARE DIE RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MAXQ® 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:260 系列:73S12xx 核心处理器:80515 芯体尺寸:8-位 速度:24MHz 连通性:I²C，智能卡，UART/USART，USB 外围设备:LED，POR，WDT 输入/输出数:9 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-VFQFN 裸露焊盘 包装:管件
MAXQ610X-0001+
功能描述:MAXQ610X PROG TESTED DIE WAFFLE RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MAXQ® 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:260 系列:73S12xx 核心处理器:80515 芯体尺寸:8-位 速度:24MHz 连通性:I²C，智能卡，UART/USART，USB 外围设备:LED，POR，WDT 输入/输出数:9 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-VFQFN 裸露焊盘 包装:管件
MAXQ610X-2001+
功能描述:16位微控制器 - MCU
RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
MAXQ610X-2021+
制造商:Maxim Integrated Products 功能描述:16-BIT MICROCONTROLLER WITH INFRARED MODULE - Gel-pak, waffle pack, wafer, diced wafer on film
MAXQ610X-UEI+
制造商:Maxim Integrated Products 功能描述:MAXQ610 BLANK WLP UEI - Gel-pak, waffle pack, wafer, diced wafer on film
MAXQ612
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:16-Bit Microcontrollers with Infrared Module and Optional USB